• Hi Guest. Welcome to the new forums. All of your posts and personal messages have been migrated. Attachments (i.e. images) and The (Old) Classifieds have been wiped.

    The old forums will be available for a couple of weeks should you wish to grab old images or classifieds listings content. Go Here

    If you have any issues please post about them in the Forum Feedback thread: Go Here

Quick Questions & Simple Answers.

Probably a stupid question but are all speed loaders pretty much the same? 

Need to budget for 1 to load mid caps/pistols.


As said they are however I have had a few where I've had to open them up to file off edges where the moulding wasn't cleaned up or the opening wasn't quite round externally so the adaptors didn't quite fit. The latter is more of an issue if the adaptor isn't one that came with the loader.

 
Currently suffering a brain fart, is it recommended to clean & lubricate a pistol (in this case a TM) prior to first use?

I feel a bit embarrassed asking but I figure better a bit of embarrassment than destroying my new pistol. Been a long day and the old brain tissue isn't working.

 
Currently suffering a brain fart, is it recommended to clean & lubricate a pistol (in this case a TM) prior to first use?

I feel a bit embarrassed asking but I figure better a bit of embarrassment than destroying my new pistol. Been a long day and the old brain tissue isn't working.


Brand New? Unmodified? Then no, it will be perfect out of the box

If used, strip it down, clean and lube

 
Currently suffering a brain fart, is it recommended to clean & lubricate a pistol (in this case a TM) prior to first use?

I feel a bit embarrassed asking but I figure better a bit of embarrassment than destroying my new pistol. Been a long day and the old brain tissue isn't working.
No, TM apply an appropriate amount of lube at the factory, it will work straight out of the box. 

 
Does anyone know where I can buy a custom cut off lever for Valken Alloy mk2. (Should be red mobile formatting does not allow)

 
Whats a good sight for a GBB MP7 since my Nuprol Holo keeps turning itself off?

 
Tokyo Marui G36K low/mid-cap recommendations - I'm looking for recommendations for compatible low cap's (will consider mid) for the TM G36K. In particular I was looking at the 45 round Ares lo-cap's, can anyone confirm if these are fully compatible?

@Game Cam - This may be outside of your budget but the warranty offered for the sight is second to none and it is rated for real firearms (to the best of my knowledge). Also if retaining zero is a point of consideration then you won't go wrong with the Vortex - Crossfire Red Dot.

 
Last edited by a moderator:
Whats a good sight for a GBB MP7 since my Nuprol Holo keeps turning itself off?
Not a direct answer to your question but one quick "fix" for this issue is to make sure the battery contacts aren't disconnecting - you can do this by folding some tinfoil into a small square as a buffer between battery and battery contact if this makes sense. Do this for each side of the battery and it keeps it nice and snug and could solve the issue. Plus warranty options as stated elsewhere

 
Is this the legit site to buy the burst wizard? Website looks well dodgy!

http://www.aegwizard.com/


Heard of it but why not go for something reputable rather than something like that? plenty of options

BTC

Jefftron

Titan Gate

(after a 2 second google I found airsoft world sell burst wizard stuff so why not look on there)

 
In my opinion, No.


i second this motion

heavier ammo will give you more range, but lighter ammo in an indoor setting will have a marginally faster flight time (it gets overtaken at range by heavier ammo) but more importantly it's cheaper.

 
Heard of it but why not go for something reputable rather than something like that? plenty of options

BTC 

Jefftron 

Titan Gate 
Cheers I'll look at the BTC but the jefftron full bag of mashings version isn't available for v2 and the titan is too much cash imho

Edit: seems like the BTC is out of stock eveywhere

 
Last edited by a moderator:
Has anybody had experience with a Spectre rdp and if they know where to get one? Practically everywhere sold out so assume they're no longer being produced?

 
Back
Top