Search results

I think the “gas key” is the nub at the top of that part that fits in the underside of the charging handles. Obviously there are slight differences between the firearm and airsoft M4 designs so not a direct comparison ?

Hao put the sticker on the upper left face of the BCG (opposite side to the ejection port)  it probably needs less than 1mm removing, best to take a little off and try rather than going mad with the angle grinder! I have experienced it with certain combinations of nozzle guides and charging...

The part circled in red is the cut out for the hop up wheel. To make more room you can either carefully file out some more or make the bolt carrier and nozzle guide run “lower” in the upper receiver. Hao achieves this with their BCG stickers for example.

The hop seems to be adjusting itself.  This could be the nozzle guide on the top of the bolt carrier rubbing the hop wheel as it moves forward. There should be a small scalloped section, try fettling that a bit and see if that sorts it. the cup seal on the nozzle seems to be causing excessive...

Fobus IWB from Tactical Kit. Took some heating in hot water and work with sandpaper to ensure the WE G19 fitted properly and I could get the damn thing out again ?   Craghoppers shirt was good enough for Obi Wan Nairobi so will stand up to anything I put it through ?

* Glock 19 in IWB * Three spare mags (5.11 Defender jeans extra pockets) * Torch Plenty for CQB games if you don’t go trigger happy.

First thing I would check is pull the bolt and charging handle out and check it and the inner of the receiver for sticking points, burrs and that it is suitably lubricated. While it is apart check the action of the “hammer” and sears that they move and reset smoothly. Some GT85 or similar...

I missed the last one as I could not find any details and my emails went unanswered. Will look out for the next one as I have a couple of big boxes of kit to shift! :)

I have found that Bolle Cobra glasses with antifoam wipe (Revision, as above) never fog with me (not that sweaty compared to some) Available in clear, yellow, grey and other lens colours for under £15 but they will stop 6Joule steel BBs :) DeltaMike face pro for outdoor games, but after some...

Ahh OK, I think that might be to do with the hop chambers, barrel cut outs and general build quality. Plus pushing 0.36g BBs in an AEG needs some BIG cylinder volume and spring pressure (same for HPA set ups, higher PSI and volume) and then you are still using a hop unit designed for 0.25g BBs...

okay...this might be a long post! With AEGs you have a fixed cylinder volume and spring speed. This is usually matched to barrel length / diameter and BB weight you want to use (others can chime in with formulas and typical set ups) With a GBBR when the trigger is pulled the gas is vented down...

But the Federal one is just a copy of the AngryGun one with the “pegs” at the back rotated 90deg to work with a regular valve stop. If it works as well as my modded AG one they will be more consistent and easier to adjust than the RA Tech ones

I picked up a can of the new ASG Orange (164psi) gas to test yesterday. I have been running my MWS on the ASG beige gas for ever and just bought 6 more cans from Firesupport ? Testing was done in 20degC, averaged over 10 shots, with my MWS, mag #1 and 0.32g BBs. YMMV… in fact I am sure it will...

Playing about mounting my Kywi pouches with 1” velcro one-wrap and with some off cut paracord made this quick access TQ* mount. Pull down on the red handle and it is instantly accessible.  Probably 1001 things you can do with one-wrap, need to order a big roll as so handy for strap / cable...

With some modification (cut a flat, file round circumference) the AngryGun NPAS can fit the much better quality GM or TM nozzles. FPS consistency was much better than the RATech or G&P NPAS, looking +/-2 fps with 0.32g BBs and ASG gas. Shame you can’t buy them with out the nozzle (although...

Having fielded my MWS at the great RIFT Airsoft REDCON-2 site at the weekend I found that the old TM hop rubber was on its way out and my GunsModify nozzle damaged (probably from a shattered tracer BB earlier in the year) and this led to a couple of gas dumps at in opportune moments ? I also...

I have had the same issue with a stock set up and Laylax arm. Using card board as a temporary shim to keep it central during barrel nut tightening is a great idea.   Mine was resolved by twisting the barrel a fraction off centre then tightening up the barrel nut. You don’t need to crank down...

In my mind the Clutch cover of fortunate son (much better than CCR - fight me!) or the Doom Eternal remix soundtrack. In reality “yackity sax” (Benny Hill theme)!

ASG gas in the beige / sand coloured cans. Only ever go to Abbey 144a or Nuprol Red at extremes of weather! 

370mm barrel will increase the power, cool if you are after that but a pain if you end up over chrono limit ?